Areas we work in

Specialist repointing and brickwork in North Wales

A family-run firm of brick and stone masons based in Chester, repointing, repairing and rebuilding older buildings in traditional lime mortar.

Lime repointing and brickwork in North Wales is work that K Blythin Brick & Stonework Ltd takes on alongside stone repairs and walling. Chester, our base, is minutes from the Welsh border, and the firm has 60+ years’ combined experience. If a stone cottage never dries out, or a brick terrace is shedding its faces, here is the likely cause and the cure.

Stone, slate and brick: older buildings in North Wales

Many older cottages, farmhouses and chapels in north-east Wales are grey limestone or local sandstone under Welsh slate, with field and garden walls in the same stone. The Victorian towns added terraces in the red brick and terracotta of the region’s many brickworks. Until the early twentieth century walls were bedded and pointed in lime, much of it burnt in kilns on the local limestone, and most stone houses were lime rendered or limewashed.

What cement does to a lime-built wall

A solid wall has no cavity. It takes in rain and lets it evaporate, mostly through the joints. Lime mortar is softer and more open than the stone or brick beside it, so it takes the weathering itself. Cement is hard, brittle and close to watertight. Once joints are refilled with it, or a wall is cement rendered, rain still gets in through fine cracks but cannot get back out. Driving rain off the Irish Sea and upland frost do the rest.

The usual signs, not all of them down to cement:

  • Damp patches and blown plaster indoors, because the wall stays wet.
  • Sandstone and brick faces flaking away (spalling) as trapped water freezes.
  • Boundary and retaining walls that bulge or lean as old lime washes out of the core.
  • Damp at floor level where blocked air bricks leave a timber floor unventilated: a vent problem, not a pointing one.

What we take on: repointing and brickwork in North Wales

Traditional lime pointing is our specialism. Failed cement is raked out by hand, so the edges of the stone or brick stay whole. In goes a lime mortar made with local sand and matched to the wall. Joints are finished by hand, then protected until the mortar cures.

Brick terraces and chimney stacks come under our heritage bricklaying: bricks whose faces have blown are cut out and replaced to suit the wall. Our stonemasonry covers rebedding and replacing failed stone. Where a sound block has lost its face, we build it back up in Lithomex, a lime-based repair mortar for stone.

Walls are our work too, new or repaired: mortared stone walling and traditional dry stone walling. The rest is paving and cobbles, plus general building restoration and repairs, for homes and commercial property.

On site at your property

We keep a tidy site, which matters on a narrow lane, in a shared farmyard or on a terrace opening onto the pavement.

We are accredited by SafeContractor and belong to Constructionline, and a health and safety officer of our own is on site. That helps if you answer for a commercial building, a rented house or a chapel.

Jobs you can read about

We have no North Wales case study on the site yet. The nearest in kind: near Tarporley in Cheshire, the damp in a mid-1800s brick farmhouse was cured once its failed cement repoint was redone in lime. Near Knowsley on Merseyside, we rebuilt a collapsed sandstone estate wall in lime. In Chester city centre, we conserved a sandstone arch using hot-lime mortar and Lithomex.

Common questions about repointing in North Wales

How can I tell cement pointing from lime?

Cement pointing is hard, grey and smooth, and often stands proud of the stone or smears over its edges. Lime is softer and paler, and a key will mark it. If the stone is wearing faster than the joint, suspect cement.

It depends. In Wales, listed building consent is handled by your local planning authority. Cadw, the Welsh Government’s historic environment service, says genuine like-for-like repairs do not normally need consent, but the test can be exacting, and swapping cement for lime changes how a wall looks. Ask the authority’s conservation officer before any mortar comes out. We treat period and listed buildings sympathetically.

Which parts of North Wales do you cover?

Ours is a family-run firm in Chester, minutes from the border, and we cover the towns of North Wales. It is a big region, so tell us where the property is and we will say plainly if we can take it on.

Damp stone, flaking brick or a leaning wall in North Wales: let us know what you have noticed. Get a quote, or ring 07903 015639.

How a job runs

There are no shortcuts in heritage work. Every wall is repaired the slow, traditional way, the way it was built.

  1. Rake out

    We rake out failed cement and perished mortar by hand, back to sound material, without ever damaging the arris of the brick or stone.

  2. Match the mix

    A bespoke lime mortar is mixed to the historic fabric and local sand, matched for colour, strength and texture to the original.

  3. Point by hand

    Every joint is pressed and finished by hand, struck, weathered or flush to suit the wall, so the repair reads as original.

  4. Protect and cure

    Lime cures slowly. We protect the work from sun, rain and frost while it carbonates, so it sets hard, breathable and lasting.

Areas we work in

Chester, the North West and North Wales

Based in Chester. Choose an area to see the work we do there.

Tell us about the building

Tell us what you are seeing and we will be in touch. Photos are welcome by email.

07903 015639 info@kblythinstonemasons.co.uk

Chester, working across Wirral, North Wales, Liverpool, Warrington, Greater Manchester, Knutsford, East Cheshire and Crewe